Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of BERGAMID® B700W25 - PA6 - Avient Corporation

Material Data Center offers the following functions for BERGAMID® B700W25:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergamid B datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà
Any use of this information falls under the rules of our disclaimer.
Testo del prodotto
BERGAMID B700W25, PA6 unreinforced
general-purpose injection molding grades
impact modified
UL-listing
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 2900 / - MPa ISO 527
Carico unitario a trazione 70 / - MPa ISO 527
Deformazione a snervamento 4 / - % ISO 527
Deformazione a rottura 25 / - % ISO 527
Resistenza all'urto Charpy, +23°C N / - kJ/m² ISO 179/1eU
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 65 / * °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 170 / * °C ISO 75-1/-2
ASTM Data
UL 94 combustibilitá HB - UL 94
Spessore testati 0.8 mm -
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Costante dielettrica relativa, 1MHz 3.4 / - - IEC 62631-2-1
Resistività volumica 1E12 / - Ohm*m IEC 62631-3-1
Resistività superficiale * / 1E12 Ohm IEC 62631-3-2
Rigidità dielettrica 100 / - kV/mm IEC 60243-1
Res. Alle correnti striscianti superficiali 600 / - - IEC 60112
Altre Proprietàsecco/condUnitáNorma del test
Massa volumica 1100 / - kg/m³ ISO 1183
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Caratteristiche speciali
Alto urto o modificato all'urto
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, Near East/Africa
Altre informazioni
Stampaggio ad Iniezione
PREPROCESSING
Max. Water Content 0,1%
Pre-drying: 80°C 4 Hours
PROCESSING
Melt Temperature 250-270°C
Mould Temperature 40-80°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.